NAGRA 4.2 MONO ANALOGUE REEL TO REEL TAPE RECORDER
Serial number,L 7525 none pilot. EQ is CCIR and it has a 50 Hz stroboscopic roller
THE FRONT OR THIS
NAGRA IS IN POOR CONDITION BUT IT IS IN GOOD WORKING ORDER,
IT HAS BEEN SERVICED BY ``MIKE HARRIS SOUND SERVICES``AND HAS A 3 MONTH GUARANTEE
With shoulder strap fixing screw, a copy of Instruction manual, mono to stereo jack adapter and a new roll of tape that was used to line up the recorder, now has 1 & 8K at -8dB test frequency, and some music to test the playback,
has the following features:
Two microphone inputs 50 or 200 Ohm Dynamic, a line input on banana plugs or the 6 pin Tuchel ASS socket, It has Direct or off Tape monitoring and metering, Monitoring selector with monitor speaker and level control, Manual or Automatic headphone monitoring with level control, it has 1 & 2 high pass and 1&2 LAF low freq attenuation filters, 3 Taps speeds- 38, 19, 9.5cm/s (15-7.5-3.75ips). 50 Hz strobe roller, ruby tape guides, Reference generator set a 1 k at -8dB, manual recording level, Low Frequency Attenuation, Metering of Battery and Pilot level. Silicon rubber pinch wheel and drive belts, you can run 7" tape spools with the lid open, It also has a clean battery compartment and box cover has no battery corrosion.
I have set the bias for LPR35 when set on the SPEED & EQ to LP for long play tape and SM911 when set to STD standard play tape
The Perspex lid has some scratches but is in good condition
This is a full track mono recorder CCIR recorder, the 50 or 60 Hz Pilot sync has not had the circuit bards fitted
BELOW RIGHT, See pilot link plug socket , above the pilot link socket and handle fixing screw are the two large case opening screws, please note; only unscrew 3 or 4 turn do not take right out, or parts could fall into the recorder, so switch off before opening.
ABOVE LEFT, Two microphone inputs 3 pin XLR socket , Line Input on a ACC socket is a 6 pin Tuchel plug or 4 mm banana plugs. The VOL is the playback level control, next to the handle fixing screw
ABOVE RIGHT, The 4 mm banana sockets are 4.4 volts output at 600 ohm if you feed this output to a Stereo Nagra you must use the QCSE lead or a copy with a 47K ohm pad. Or use the 7 pin MIXER socket that has a Playback or Direct output, leads can be made to order. For the POWER PACK, you can use the 24 volts ATN power supply, the 35 volts ATN 2 or ATN 3 power supplies, or the UAP11 power supply on main page, The 3 pin XLR plug the balanced output
The back of the recorder has some dents , The battery box and cover are in good order and has no battery corrosion.
Above Left, Tape head are good condition and it has a new pinch wheel.
Above Right, the lid hinges are scratched but in good working order
No head loss adjustment was needed when lining up the tape bias EQ and playback, this recorder is set up for SM911 & LPR35 that I have selected as closest to AGFA 468 or 368, Zonal 468 / 368 and BASF 468 or 368,
BELOW RIGHT the two Dynamic Microphone pre-amps are behind the meter, the Nagra D has no Pilot sync fitted
The recorder works from 12 x U2 batteries or external ATN mains supply (not included) see assessors 2 for power supplies
ABOVE The heads are in good order, and it has Ruby tape guides and new pinch wheel.
ABOVE RIGHT, as you can see the front panel is in poor condition, I don't know the history of this recorder and I cannot imagine how it got like that, when the inside is clean.
Nagra is the best
reel-to-reel tape recorder ever made with the best of Swiss engineering that
you are never likely to see again.
One of the joys of owning a Nagra is that it is an all in one over the shoulder recorder and when you switch it on you know it's going to work and give you a professional quality recording in any conditions.
Please note: -The Perspex lid has some scratches, and the front panel is in poor condition
Extras, mods and updates with this recorder = 10
To buy this item please telephone: Mike Harris 01932 241948 or Email, firstname.lastname@example.org